Address:North Square Road, Gaobu Town, Dongguan
Phone:+86-13711930133
Tel:+86-769-88734319
The following safety measures shall be taken when repairing and maintaining the Composite Machine:
1. When operating the Composite Machine, do not put other sundries on the body or use it as a cushion. When moving or lifting the Composite Machine, only its base is allowed to be used as the handling force point. Never use the rubber pot cover, electrical box door, electrical components on the control panel or joints on the insulation pipe of the Composite Machine to lift the Composite Machine. Abnormal handling will damage the spraying equipment of the Composite Machine.
2. Before removing or moving the protective device on the web Composite Machine or replacing the element components, the power supply must be cut off first, and live operation is not allowed. When loosening or installing the pressure joint, make sure that the pressure of the pressure air supply for the Composite Machine has been reduced to zero.
3. When disassembling and maintaining, workers should not wear earrings, watches, necklaces, bracelets and other conductive decorations to prevent accidents. Safety gloves, goggles and long sleeve work clothes must be worn during the maintenance and repair of the Composite Machine, so as to avoid body parts being scalded by high-temperature liquid hot-melt adhesive or by high-temperature component surface.
4. In case of air pressure or glue leakage in the web Composite Machine, do not continue to operate the web Composite Machine. First stop the web Composite Machine, cut off the power supply, and reduce the operating pressure to zero before maintenance. Try to stand on the plastic blanket for maintenance. Never carry out maintenance work on the Composite Machine in a flooded floor or in a very humid environment.
5. In any case, do not touch the wire connector that may be exposed to the outside world or other components with wire connection and not loose. Unless there are other personnel to assist, and in case of accident, mechanical damage or personal injury, you can immediately give help or first aid, otherwise do not disassemble and repair the Composite Machine equipment alone.
6. When cleaning the hot melt glue tank, avoid using fireworks or sharp hard tools to avoid scratching the Teflon non stick coating inside the glue barrel.
7. Do not disassemble, check and adjust any parts on the web Composite Machine, unless you have sufficient knowledge of the equipment performance. At the same time, remember that only qualified personnel can repair and maintain the web Composite Machine.
cb@zgchuanbo.com
+86-13711930133
North Square Road,
Gaobu Town, Dongguan
08:30~17:30 Monday
to Saturday
The following safety measures shall be taken when repairing and maintaining the Composite Machine:
1. When operating the Composite Machine, do not put other sundries on the body or use it as a cushion. When moving or lifting the Composite Machine, only its base is allowed to be used as the handling force point. Never use the rubber pot cover, electrical box door, electrical components on the control panel or joints on the insulation pipe of the Composite Machine to lift the Composite Machine. Abnormal handling will damage the spraying equipment of the Composite Machine.
2. Before removing or moving the protective device on the web Composite Machine or replacing the element components, the power supply must be cut off first, and live operation is not allowed. When loosening or installing the pressure joint, make sure that the pressure of the pressure air supply for the Composite Machine has been reduced to zero.
3. When disassembling and maintaining, workers should not wear earrings, watches, necklaces, bracelets and other conductive decorations to prevent accidents. Safety gloves, goggles and long sleeve work clothes must be worn during the maintenance and repair of the Composite Machine, so as to avoid body parts being scalded by high-temperature liquid hot-melt adhesive or by high-temperature component surface.
4. In case of air pressure or glue leakage in the web Composite Machine, do not continue to operate the web Composite Machine. First stop the web Composite Machine, cut off the power supply, and reduce the operating pressure to zero before maintenance. Try to stand on the plastic blanket for maintenance. Never carry out maintenance work on the Composite Machine in a flooded floor or in a very humid environment.
5. In any case, do not touch the wire connector that may be exposed to the outside world or other components with wire connection and not loose. Unless there are other personnel to assist, and in case of accident, mechanical damage or personal injury, you can immediately give help or first aid, otherwise do not disassemble and repair the Composite Machine equipment alone.
6. When cleaning the hot melt glue tank, avoid using fireworks or sharp hard tools to avoid scratching the Teflon non stick coating inside the glue barrel.
7. Do not disassemble, check and adjust any parts on the web Composite Machine, unless you have sufficient knowledge of the equipment performance. At the same time, remember that only qualified personnel can repair and maintain the web Composite Machine.