Mobile Phone

+86-137 1193 0133

Call Us

+86-769-8873 4319

E-mail

cb@zgchuanbo.com
Contact Us

Address:North Square Road, Gaobu Town, Dongguan
Phone:+86-13711930133
Tel:+86-769-88734319

Industry News
Position: Home / News / Industry News

Standard workflow of web paper composite machine

Date:2020-12-22
Info:
 Tension control is one of the most important conditions in the process of laminating machine. If th

  Tension control is one of the most important conditions in the process of laminating machine. If the tension is not controlled properly, the paper will be wrinkled or curled, which will lead to a series of problems, such as wrinkle, silver leakage, difficulty in electronic plate alignment and high defective product rate. the web paper composite machine is a high-temperature and high-voltage equipment, a set of standard operation process can help operators to establish good operating habits, achieve safety production and increase the service life of the equipment.

Composite Machine

  Standard workflow of web paper composite machine

  1. After connecting the power supply with rated voltage of the machine, turn on the power switch of the heater, and the heater power indicator will be on.

  2. Adjust the temperature controller of rubber storage tank at 130-140 ℃ and the temperature controller of coating roller between 140-150 ℃. The above temperature is for reference only, and the actual melting point of hot melt adhesive shall prevail. At this point, the preheating procedure for the heater of the web laminating machine has been completed.

  3. Preheat for 30 minutes. After the hot melt glue in the glue tank has melted and the motor start indicator light is on, turn on the motor power switch, and then adjust the motor speed adjustment knob to the required working speed. If the motor fails to rotate, please wait until the hot melt glue melts completely.

  4. Adjust the glue amount adjustment knob, clockwise direction is thickening, counter clockwise direction is thinning, the compound machine can be adjusted to the required amount of glue.

  5. Please turn off the heater power switch 5-10 minutes before shutdown to reduce the temperature of rubber roller and rubber storage tank, so as to prevent carbonization of hot melt adhesive on rubber roller.

  6. When the heater power switch is turned off for 5-10 minutes and the temperature decreases, adjust the motor speed adjustment button to zero, and then turn off the motor power switch. Turn off the power supply of the input machine to complete the shutdown procedure.


E-mail

cb@zgchuanbo.com

Phone

+86-13711930133

address

North Square Road,
Gaobu Town, Dongguan

WORKING TIME

08:30~17:30 Monday
to Saturday

Copyright © 2020 Dongguan Chuanbo Machinery Equipment Co., Ltd.
Home / News / Industry News

Standard workflow of web paper composite machine

  Tension control is one of the most important conditions in the process of laminating machine. If the tension is not controlled properly, the paper will be wrinkled or curled, which will lead to a series of problems, such as wrinkle, silver leakage, difficulty in electronic plate alignment and high defective product rate. the web paper composite machine is a high-temperature and high-voltage equipment, a set of standard operation process can help operators to establish good operating habits, achieve safety production and increase the service life of the equipment.

Composite Machine

  Standard workflow of web paper composite machine

  1. After connecting the power supply with rated voltage of the machine, turn on the power switch of the heater, and the heater power indicator will be on.

  2. Adjust the temperature controller of rubber storage tank at 130-140 ℃ and the temperature controller of coating roller between 140-150 ℃. The above temperature is for reference only, and the actual melting point of hot melt adhesive shall prevail. At this point, the preheating procedure for the heater of the web laminating machine has been completed.

  3. Preheat for 30 minutes. After the hot melt glue in the glue tank has melted and the motor start indicator light is on, turn on the motor power switch, and then adjust the motor speed adjustment knob to the required working speed. If the motor fails to rotate, please wait until the hot melt glue melts completely.

  4. Adjust the glue amount adjustment knob, clockwise direction is thickening, counter clockwise direction is thinning, the compound machine can be adjusted to the required amount of glue.

  5. Please turn off the heater power switch 5-10 minutes before shutdown to reduce the temperature of rubber roller and rubber storage tank, so as to prevent carbonization of hot melt adhesive on rubber roller.

  6. When the heater power switch is turned off for 5-10 minutes and the temperature decreases, adjust the motor speed adjustment button to zero, and then turn off the motor power switch. Turn off the power supply of the input machine to complete the shutdown procedure.



Dongguan Chuanbo Machinery Equipment Co., Ltd.